Why is it easy to drop ink after printing on Yaguang paper?

In the printing process of matt paper, there is often such a problem that the drying performance is poor, the drying speed is slow, and it is easy to “discard ink” during the post-press processing, especially when printing black ink in the field, to give product quality, The production cycle has had an impact. To this end, we look for reasons from the following aspects.

First, the pH of the paper is tested. Because the pH value of the paper is one of the main factors affecting the drying of the print, acidic paper is less dry. After monitoring several commonly used brands of matte paper, the pH value is between 7 and 8, which is a neutral partial alkali, both in the normal range. At the same time, the moisture content of matt paper was also monitored and monitored. The value ranged from 8% to 9%, which was within the normal range.

Secondly, the pH of the fountain solution is tested. The pH of the fountain solution is basically stable between 4.8 and 5.2. At the same time, the amount of water is strictly controlled. In the production process, the amount of water is continuously reduced, basically meeting the requirement of water-ink balance, and minimizing the degree of ink emulsification.

Third, analyze the ink thickness. Although the black ink actually has a large amount of ink, it is not overprinted, and the lightly rubbing in the high-profile part of black ink also “discards ink”, indicating that the thickness of the ink layer is not greatly affected.

Fourth, control the ambient temperature and humidity. The temperature was controlled at 25°C and the relative humidity was controlled at 65%. At the same time, the delivery height is also reduced to a minimum, basically 200 to 300 sheets.

Fifth, choose special inks that are specially suitable for printing on matt paper, and also try to add driers to the ink.

In view of the above factors that may affect the drying of blots, corresponding measures were taken one by one, but the results were not satisfactory and the problems were not solved fundamentally.

According to the analysis, the main reasons for the poor drying of the matte paper imprints are the particularity of the matt paper itself and the specificity of the black ink pigment.

Due to the small degree of sizing, the matt paper has a loose structure and a rough surface, so its absorption is strong and the binder in the ink can be quickly absorbed. The yellow, magenta, and cyan pigments are generally made of inorganic or organic pigments, while the black ink uses carbon black (elemental carbon) as the pigment, and the carbon black is non-drying. In general, black ink is better than other color inks. Dry slowly. In addition, the adhesion of carbon black and the binder is lower than other inorganic or organic pigments. This causes the matte paper to absorb the binder in the ink too quickly and float the carbon black on the surface of the paper.

The use of matt paper is becoming more and more widespread. Some printing companies use post-printing oils to alleviate this problem. This will not only increase the cost, prolong the production cycle, but also the biggest hazard is to change the original characteristics of matt paper, and the color is also affected.

In order to meet the customer's requirement for black ink on the matte paper and solve the problem of “disappearing ink” at the same time, some people have made some attempts. One is to use yellow, magenta, and cyan inks as the network cable version to obtain color ink overlays. Black; second is the use of color method, the yellow, magenta, cyan ink mixed black ink to avoid the black ink in the "carbon black." Because pigments in yellow, magenta, and cyan are basically inorganic pigments, their drying properties and adhesion are significantly better than those of carbon black.

Container glass 

Container glass has a lower magnesium oxide and sodium oxide content than flat glass, and a higher Silica, Calcium oxide, and Aluminum oxide content. Its higher content of water-insoluble oxides imparts slightly higher chemical durability against water, which is required for storage of beverages and food. Most container glass is soda-lime glass, produced by blowing and pressing techniques, while some laboratory Glassware is made from borosilicate glass.

Usage: Liquor/Wine/Beverage

Material: Extra-flint, high-flint and flint glass

Technology: Machine made

Volume: 50 to 3000ml or as your requirements

Weight: 150 to 2000g and so on

Sealing type: Screw cap or cork

Painting: Any color as you requirement

Quality control: SGS, FDA, ISO9001, ISO14001

Deep processing: Silk screen, decal, spray painting, electroplating, frosting, sand blasting.

Delivery term: EXW, FOB, CIF

Payment terms: T/T

Lead time: New design drawing confirm within 3days, Sample mold within 20 days, bulk molds within 30 days, produce in bulk within 30 days



Q:  Are you a manufacture or a trading company?

A:  We are a manufacture which located in Chengdu city and Yibin city, Sichuan, China.

Q:  Can you customize the products?

A:  Yes, we are professional to customize glass bottle, we can design the new drawings and open the new molds according to your requirement.

Q:  Do you provide free sample?

A:  Yes, for cooperation sincerity, we are glad to provide you samples for free, but for new customer, the express cost need to be paid.

Q:  What is your MOQ?

A:  Our only standard for MOQ is a 40 feet container.

Q:  How long is your sample lead time, mold need time and production lead time?

A:  New design drawing confirm within 3 days, sample mold within 20 days, bulk molds within 30 days, produce in bulk within 30 days

Jar or Glass Container

Olive Oil Glass Bottle,Super Flint Bottle,Oil Glass Bottle,Glass Spraying Bottle

SICHUAN YIBIN GLOBAL GROUP CO.,LTD. , https://www.globalglassbottle.com